$63.22
$91.04
The Launch X-431 S2-2 Sensorbox is a cutting-edge diagnostic tool designed to test and simulate most vehicle sensors, providing quick and accurate troubleshooting of the ECU (Engine Control Unit). It works in combination with LAUNCH X-431 diagnostic tools to maximize repair shop efficiency and revenue. The S2-2 Sensorbox allows technicians to simulate various sensor conditions, manually write waveform data, and measure a wide range of electrical signals, all in one compact and powerful device. Download User Manual Here Download Product Leaflet Here Compatible with the following LAUNCH scanners: Offline PRO Series: X431 Pro3 Link, X431 Throttle, X431 Pad II AE, X431 Torque, X431 Turbo Online PRO Series: X431 Pros Star, X431 Pros Elite, X431 Pro (V5.0, Pros V5.0) X431 V V5.0, X431 Pro3S V5.0, X431 Pro3 Apex, X431 Pro3 Ace X431 Pro3 (V ) Elite, X431 Pro5 SmartLink PAD Series: X431 PAD V Elite, X431 PAD VII Elite IMMO Series: X431 IMMO Elite, X431 IMMO PLUS NOTE: Not compatible with older PRO5, CRP919X BT/CRP919E BT, PRO3S V2.0, V 2.0 or V 4.0.If you are unsure if your device is supported, please contact with your serial number. Key Features – ECU Troubleshooting and Diagnostics: Checks the ECU’s operational status. Simulates working conditions of sensors without replacing parts. Supports manual writing of waveform data. Allows simulation of special working conditions of sensors for more accurate diagnosis. – Advanced Sensor and Actuator Simulation: Simulates input signals of the automotive electronic control system. Simulates output control signals to diagnose actuators like idle motors and EGR solenoid valves. Simulates throttle and pedal sensors, airflow meters, oxygen sensors, temperature sensors, EGR sensors, and injector sensors. – Multimeter Functionality: Measures resistance, voltage (AC/DC), capacitance, frequency, and pulse signals. Provides high-precision electrical measurements for detailed diagnostics. – Intuitive Interface and Operation: One-click access to sensor, actuator, waveform, and multimeter menus. Customizable waveforms and output signals. Defined and drawn waveforms with adjustable frequency, amplitude, offset, and phase. Supports both predefined and hand-drawn waveforms for greater flexibility. Technical Specifications Sensor Module Parameter Specification Number of Channels 2 Precision 1% Amplitude Range 0 – 20 V Max Output Current 20 mA Predefined Frequency Range 0 – 20 kHz Square Wave Signal Pulse Frequency 0 – 15 kHz Square Wave Signal Duty Cycle 0 – 100% Power Supply Battery-powered (max 20 mA) or external (2A) USB USB2.0 Type B (charging and power supply, 5V) DC Voltage Simulation Supported Fixed Frequency Simulation Supported Predefined Waveform Simulation Supported Hand-drawn Waveform Simulation Supported Signal Generator Interface 2 External Power Supply Port 1 Solenoid Interface 1 Multimeter Interface 2 Working Temperature 0°C – 50°C Storage Temperature -30°C – 70°C Multimeter Parameter Range DC Voltage 0 V – 700 V AC Voltage 0 V – 700 V Resistance 0 Ω – 40 MΩ Capacitance 0 F – 100 µF (max 30 s) Diode Test 0 V – 1.5 V Continuity Detection Sounds below 30 Ω Waveform Settings Parameter Options Waveforms Forward sine wave, reverse sine wave, forward square wave, reverse square wave, medium voltage, straight line, high/low voltage straight line, triangle wave, trapezoidal wave Frequency Adjustable Amplitude Adjustable Offset Adjustable Phase Adjustable Duty Cycle Adjustable Signal Sync Simultaneous output on CH1 and CH2 Hand-Drawn Waveform Settings Parameter Options Total Frame 1 – 3 (100, 200, or 300 points) Edit Frame Single frame or all frames Frequency Adjustable Amplitude Adjustable Offset Adjustable Indicator Light Status Green Lamp (Battery Status): Steady on – Normal battery level Intermediate flashing – Low battery level Slow flashing – Charging in progress Red Lamp (Diagnostic Tool Status): Steady on – Connected Flashing – Disconnected Connection and Operation Connect via USB: Insert the USB cable into the sensor module and the diagnostic tool. Power On: Press and hold the power button for 3 seconds. Status Indicators: Green lamp steady – Ready to use. Green lamp flashing – Battery low or charging. Red lamp steady – Connected to diagnostic tool. Red lamp flashing – Disconnected. Diagnostic Menu: Use the diagnostic tool’s menu to access the Sensor Simulator interface. Benefits Reduces downtime by quickly diagnosing sensor-related issues. Helps avoid unnecessary part replacement. Supports customizable and hand-drawn waveforms for tailored diagnostics. Provides high-precision measurement for detailed analysis. Portable and compact design for easy use in various environments. Why Choose the Launch X-431 S2-2 Sensorbox? The Launch X-431 S2-2 Sensorbox is an essential tool for any professional automotive repair shop. Its ability to simulate and diagnose a wide range of sensor faults, combined with multimeter functionality and waveform customization, makes it a versatile and powerful solution for ECU troubleshooting and sensor testing. Its compatibility with the latest LAUNCH diagnostic tools ensures that technicians have the right tool to solve complex diagnostic problems efficiently.
Accessories & Parts
